Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RADILON A CW250UK 3031 BK - PA66-MF25 - RadiciGroup High Performance Polymers

Material Data Center offers the following functions for RADILON A CW250UK 3031 BK:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Radilon A datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 機械的特性 - 熱的特性 - 電気的特性. - その他の特性.
Any use of this information falls under the rules of our disclaimer.
商品の説明文
PA66 25% mineral filled injection moulding grade. Improved UV resistance. Black colour.

Suitable for parts requiring good dimensional stability, reduced shrinkage and low warpage. Intended to resist to outdoor exposure.
Processing/Physical Characteristics乾燥/調湿単位テスト基準
ISO データ
メルトボリュームレイト, MVR 66 / * cm³/10min ISO 1133
温度 275 / * °C -
荷重 2.16 / * kg -
成形収縮率, 平行 0.5 / * % ISO 294-4, 2577
成形収縮率, 直角 0.9 / * % ISO 294-4, 2577
機械的特性乾燥/調湿単位テスト基準
ISO データ
引張弾性率 7100 / 3000 MPa ISO 527
破壊応力 95 / 55 MPa ISO 527
破壊ひずみ 5 / 25 % ISO 527
シャルピー衝撃強さ, +23°C 70 / - kJ/m² ISO 179/1eU
シャルピー衝撃強さ, -30°C 35 / - kJ/m² ISO 179/1eU
ノッチ付きシャルピー衝撃強さ, +23°C 5 / - kJ/m² ISO 179/1eA
熱的特性乾燥/調湿単位テスト基準
ISO データ
溶融温度, 10°C/min 260 / * °C ISO 11357-1/-3
厚さhでの燃焼性 HB / * class IEC 60695-11-10
試験片の厚さ 0.8 / * mm -
電気的特性.乾燥/調湿単位テスト基準
ISO データ
体積抵抗率 1E13 / 1E11 Ohm*m IEC 62631-3-1
表面抵抗率 * / 1E10 Ohm IEC 62631-3-2
その他の特性.乾燥/調湿単位テスト基準
吸水率 6.4 / * % Sim. to ISO 62
吸湿率 1.5 / * % Sim. to ISO 62
密度 1340 / - kg/m³ ISO 1183
特殊な特性
成形加工法.
射出成形.
納入形状.
顆粒., 黒
添加剤.
離型剤.
特殊な特性.
紫外線安定化., 熱安定化.
な特性
Low Warpage
領域別の利用可能性
北アメリカ., ヨーロッパ., アジア/太平洋地域., 南・中央アメリカ., 近東/アフリカ
その他の情報
村遜速揃
The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water content for best processing is 0.15%. Typical conditions with a desiccant drier: temperature 80 ° C, dew point -20 ° C or below, time 2-4 h or more. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters
Melt TemperatureMold TemperatureInjection Speed
280 - 300°C80 - 100°Cmedium-high
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.